Új hozzászólás Aktív témák

• #85867 #63718632 törölt tag csixy #85865

  Új Válasz 2022-09-24 16:13:23 #85867

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  

  #63718632

  törölt tag

  válasz csixy #85865 üzenetére

  Nekem van egy EMTEC X200-as külső SSD-m. Itt az infó róla.
  michael@hpzbook:~
$ sudo hdparm -I /dev/sdc
/dev/sdc:
ATA device, with non-removable media
    Model Number:       SATA SSD                                
    Serial Number:      A0910718148000042587
    Firmware Revision:  SBFM61.5
    Transport:          Serial, ATA8-AST, SATA 1.0a, SATA II Extensions, SATA Rev 2.5, SATA Rev 2.6, SATA Rev 3.0
Standards:
    Supported: 11 10 9 8 7 6 5 
    Likely used: 11
Configuration:
    Logical        max    current
    cylinders    16383    16383
    heads        16    16
    sectors/track    63    63
    --
    CHS current addressable sectors:    16514064
    LBA    user addressable sectors:   268435455
    LBA48  user addressable sectors:   500118192
    Logical  Sector size:                   512 bytes
    Physical Sector size:                   512 bytes
    Logical Sector-0 offset:                  0 bytes
    device size with M = 1024*1024:      244198 MBytes
    device size with M = 1000*1000:      256060 MBytes (256 GB)
    cache/buffer size  = unknown
    Form Factor: less than 1.8 inch
    Nominal Media Rotation Rate: Solid State Device
Capabilities:
    LBA, IORDY(can be disabled)
    Queue depth: 32
    Standby timer values: spec'd by Standard, no device specific minimum
    R/W multiple sector transfer: Max = 16    Current = 16
    DMA: mdma0 mdma1 mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 
         Cycle time: min=120ns recommended=120ns
    PIO: pio0 pio1 pio2 pio3 pio4 
         Cycle time: no flow control=120ns  IORDY flow control=120ns
Commands/features:
    Enabled    Supported:
       *    SMART feature set
            Security Mode feature set
       *    Power Management feature set
       *    Write cache
       *    Look-ahead
       *    Host Protected Area feature set
       *    WRITE_BUFFER command
       *    READ_BUFFER command
       *    NOP cmd
       *    DOWNLOAD_MICROCODE
            SET_MAX security extension
       *    48-bit Address feature set
       *    Device Configuration Overlay feature set
       *    Mandatory FLUSH_CACHE
       *    FLUSH_CACHE_EXT
       *    SMART error logging
       *    SMART self-test
       *    General Purpose Logging feature set
       *    WRITE_{DMA|MULTIPLE}_FUA_EXT
       *    WRITE_UNCORRECTABLE_EXT command
       *    {READ,WRITE}_DMA_EXT_GPL commands
       *    Segmented DOWNLOAD_MICROCODE
       *    Gen1 signaling speed (1.5Gb/s)
       *    Gen2 signaling speed (3.0Gb/s)
       *    Gen3 signaling speed (6.0Gb/s)
       *    Native Command Queueing (NCQ)
       *    Phy event counters
       *    READ_LOG_DMA_EXT equivalent to READ_LOG_EXT
            DMA Setup Auto-Activate optimization
            Device-initiated interface power management
       *    Software settings preservation
       *    DOWNLOAD MICROCODE DMA command
       *    SET MAX SETPASSWORD/UNLOCK DMA commands
       *    WRITE BUFFER DMA command
       *    READ BUFFER DMA command
       *    DEVICE CONFIGURATION SET/IDENTIFY DMA commands
       *    Data Set Management TRIM supported (limit 8 blocks)
Security: 
    Master password revision code = 65534
        supported
    not    enabled
    not    locked
    not    frozen
    not    expired: security count
        supported: enhanced erase
    20min for SECURITY ERASE UNIT. 60min for ENHANCED SECURITY ERASE UNIT.
Checksum: correct
michael@hpzbook:~
$ 

Új hozzászólás Aktív témák