-
PROHARDVER!
Arduino hardverrel és szoftverrel foglakozó téma. Minden mikrovezérlő ami arduinoval programozható, és minden arduino program, board, és hardverrel kapcsolatos kérdések helye.
Új hozzászólás Aktív témák
-
válasz
daninet #22508 üzenetére
Azt írja, nem ebben a sorrendben kell megadni a paramétereket! Hogy a példában miért így van, azt nem tudom, talán az idf automatikusan javítja.
A helyes sorrendet itt tudod megnézni: [link]typedef struct {
int gpio_num; /*!< the LEDC output gpio_num, if you want to use gpio16, gpio_num = 16 */
ledc_mode_t speed_mode; /*!< LEDC speed speed_mode, high-speed mode (only exists on esp32) or low-speed mode */
ledc_channel_t channel; /*!< LEDC channel (0 - LEDC_CHANNEL_MAX-1) */
ledc_intr_type_t intr_type; /*!< configure interrupt, Fade interrupt enable or Fade interrupt disable */
ledc_timer_t timer_sel; /*!< Select the timer source of channel (0 - LEDC_TIMER_MAX-1) */
uint32_t duty; /*!< LEDC channel duty, the range of duty setting is [0, (2**duty_resolution)] */
int hpoint; /*!< LEDC channel hpoint value, the range is [0, (2**duty_resolution)-1] */
struct {
unsigned int output_invert: 1;/*!< Enable (1) or disable (0) gpio output invert */
} flags; /*!< LEDC flags */
} ledc_channel_config_t;
/**
* @brief Configuration parameters of LEDC timer for ledc_timer_config function
*/
typedef struct {
ledc_mode_t speed_mode; /*!< LEDC speed speed_mode, high-speed mode (only exists on esp32) or low-speed mode */
ledc_timer_bit_t duty_resolution; /*!< LEDC channel duty resolution */
ledc_timer_t timer_num; /*!< The timer source of channel (0 - LEDC_TIMER_MAX-1) */
uint32_t freq_hz; /*!< LEDC timer frequency (Hz) */
ledc_clk_cfg_t clk_cfg; /*!< Configure LEDC source clock from ledc_clk_cfg_t.
Note that LEDC_USE_RC_FAST_CLK and LEDC_USE_XTAL_CLK are
non-timer-specific clock sources. You can not have one LEDC timer uses
RC_FAST_CLK as the clock source and have another LEDC timer uses XTAL_CLK
as its clock source. All chips except esp32 and esp32s2 do not have
timer-specific clock sources, which means clock source for all timers
must be the same one. */
bool deconfigure; /*!< Set this field to de-configure a LEDC timer which has been configured before
Note that it will not check whether the timer wants to be de-configured
is binded to any channel. Also, the timer has to be paused first before
it can be de-configured.
When this field is set, duty_resolution, freq_hz, clk_cfg fields are ignored. */
} ledc_timer_config_t;
Új hozzászólás Aktív témák
- Xiaomi Redmi 14 PRO 5 G 8/256 DUAL garanciával
- Dell Precision 7670 FHD+ i9-12950HX 16C / 64G D5 / 1T G4 / Quadro RTX A4500 16GB / HU vb Pro tervező
- LG OLED55G42LW LG Gyári garancia 3 év
- HP EliteBook 840G6 ! AKCIÓ!!! a készlet erejéig!
- Kobo Aura Edition 2 (N236) 6" háttérvilágításos kijelzővel, 4 GB-os tárhellyel - jó állapotban
- Csere-Beszámítás! RTX Számítógép PC Játékra! R5 8400F / RTX 3070Ti / 32GB DDR5 / 1TB SSD
- AKCIÓ! MSI B460M i5 10400F 16GB DDR4 512GB SSD RX 6650XT 8GB Cooler Master MB600L Chieftec 600W
- ÁRGARANCIA! Épített KomPhone i5 14600KF 32/64GB RAM RTX 5070 12GB GAMER PC termékbeszámítással
- ÁRGARANCIA!Épített KomPhone i7 14700KF 32/64GB RAM RTX 5070Ti 16GB GAMER PC termékbeszámítással
- Kingmax 2x2GB DDR3 RAM eladó
Állásajánlatok
Cég: Promenade Publishing House Kft.
Város: Budapest
Cég: PCMENTOR SZERVIZ KFT.
Város: Budapest