Új hozzászólás Aktív témák

• #601 vasszarvas tag

  Új Válasz 2012-11-13 13:12:09 #601

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  vasszarvas

  tag

  Nem akar csinálni könyvtárat vagy valami ilyesmi...

  

  root@OpenWrt:~# dmesg
  Linux version 2.6.32.27 (jow@nd-build-02.linux-appliance.net) (gcc version 4.3.3 (GCC) ) #5 Wed Dec 21 01:59:33 CET 2011
  prom: fw_arg0=00000009, fw_arg1=a1f67fb0, fw_arg2=a1f68470, fw_arg3=00000008
  MyLoader: sysp=aaaa5554, boardp=aaaa5554, parts=aaaa5554
  bootconsole [early0] enabled
  CPU revision is: 00019374 (MIPS 24Kc)
  Atheros AR9130 rev 2, CPU:400.000 MHz, AHB:200.000 MHz, DDR:400.000 MHz
  Determined physical RAM map:
  memory: 02000000 @ 00000000 (usable)
  Initrd not found or empty - disabling initrd
  Zone PFN ranges:
  Normal 0x00000000 -> 0x00002000
  Movable zone start PFN for each node
  early_node_map[1] active PFN ranges
  0: 0x00000000 -> 0x00002000
  On node 0 totalpages: 8192
  free_area_init_node: node 0, pgdat 802dcc40, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
  Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  Kernel command line: rootfstype=squashfs,yaffs,jffs2 noinitrd console=ttyS0,1152 00 board=WRT160NL
  PID hash table entries: 128 (order: -3, 512 bytes)
  Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  Primary instruction cache 64kB, VIPT, 4-way, linesize 32 bytes.
  Primary data cache 32kB, 4-way, VIPT, cache aliases, linesize 32 bytes
  Writing ErrCtl register=00000000
  Readback ErrCtl register=00000000
  Memory: 29276k/32768k available (2126k kernel code, 3492k reserved, 423k data, 1 52k init, 0k highmem)
  SLUB: Genslabs=7, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  Hierarchical RCU implementation.
  NR_IRQS:56
  Calibrating delay loop... 266.24 BogoMIPS (lpj=1331200)
  Mount-cache hash table entries: 512
  NET: Registered protocol family 16
  MIPS: machine is Linksys WRT160NL
  bio: create slab <bio-0> at 0
  Switching to clocksource MIPS
  NET: Registered protocol family 2
  IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  TCP: Hash tables configured (established 1024 bind 1024)
  TCP reno registered
  NET: Registered protocol family 1
  squashfs: version 4.0 (2009/01/31) Phillip Lougher
  Registering mini_fo version $Id$
  JFFS2 version 2.2. (NAND) (SUMMARY) Š 2001-2006 Red Hat, Inc.
  yaffs Dec 10 2011 18:14:12 Installing.
  msgmni has been set to 57
  io scheduler noop registered
  io scheduler deadline registered (default)
  Serial: 8250/16550 driver, 1 ports, IRQ sharing disabled
  serial8250.0: ttyS0 at MMIO 0x18020000 (irq = 11) is a 16550A
  console [ttyS0] enabled, bootconsole disabled
  Atheros AR71xx SPI Controller driver version 0.2.4
  m25p80 spi0.0: s25fl064k (8192 Kbytes)
  spi0.0: searching for MyLoader partition table at offset 0x10000
  spi0.0: searching for MyLoader partition table at offset 0x20000
  spi0.0: searching for MyLoader partition table at offset 0x30000
  spi0.0: searching for MyLoader partition table at offset 0x40000
  spi0.0: no MyLoader partition table found
  Searching for RedBoot partition table in spi0.0 at offset 0x7fe000
  Searching for RedBoot partition table in spi0.0 at offset 0x7ff000
  No RedBoot partition table detected in spi0.0
  6 wrt160nl partitions found on MTD device spi0.0
  Creating 6 MTD partitions on "spi0.0":
  0x000000000000-0x000000040000 : "u-boot"
  0x000000040000-0x000000170000 : "kernel"
  0x000000170000-0x0000007e0000 : "rootfs"
  mtd: partition "rootfs" set to be root filesystem
  mtd: partition "rootfs_data" created automatically, ofs=34E000, len=492000
  0x00000034e000-0x0000007e0000 : "rootfs_data"
  0x0000007e0000-0x0000007f0000 : "nvram"
  0x0000007f0000-0x000000800000 : "art"
  0x000000040000-0x0000007e0000 : "firmware"
  ag71xx_mdio: probed
  eth0: Atheros AG71xx at 0xb9000000, irq 4
  Registering RTL8306SD switch with Chip ID: 0x5988, version: 0x0000
  eth0: connected to PHY at ag71xx-mdio:00 [uid=00008306, driver=Realtek RTL8306S]
  eth1: Atheros AG71xx at 0xba000000, irq 5
  eth1: connected to PHY at ag71xx-mdio:04 [uid=00008306, driver=Realtek RTL8306S]
  Atheros AR71xx hardware watchdog driver version 0.1.0
  ar71xx-wdt: timeout=15 secs (max=21)
  TCP westwood registered
  NET: Registered protocol family 17
  802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  All bugs added by David S. Miller <davem@redhat.com>
  VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  Freeing unused kernel memory: 152k freed
  Please be patient, while OpenWrt loads ...
  input: gpio-buttons as /devices/platform/gpio-buttons/input/input0
  Button Hotplug driver version 0.3.1
  Registered led device: wrt160nl:blue:power
  Registered led device: wrt160nl:amber:wps
  Registered led device: wrt160nl:blue:wps
  Registered led device: wrt160nl:blue:wlan
  ar71xx: pll_reg 0xb8050014: 0x13000a44
  eth0: link up (100Mbps/Full duplex)
  mini_fo: using base directory: /
  mini_fo: using storage directory: /overlay
  eth0: link down
  device eth0 entered promiscuous mode
  PPP generic driver version 2.4.2
  NET: Registered protocol family 24
  ar71xx: pll_reg 0xb8050014: 0x13000a44
  eth0: link up (100Mbps/Full duplex)
  br-lan: port 1(eth0) entering forwarding state
  Compat-wireless backport release: compat-wireless-2011-11-08-1-g4ab9b62
  Backport based on wireless-testing.git master-2011-11-15
  ar71xx: pll_reg 0xb8050018: 0x13000a44
  eth1: link up (100Mbps/Full duplex)
  cfg80211: Calling CRDA to update world regulatory domain
  SCSI subsystem initialized
  cfg80211: World regulatory domain updated:
  cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  usbcore: registered new interface driver usbfs
  usbcore: registered new interface driver hub
  usbcore: registered new device driver usb
  ath: EEPROM regdomain: 0x0
  ath: EEPROM indicates default country code should be used
  ath: doing EEPROM country->regdmn map search
  ath: country maps to regdmn code: 0x3a
  ath: Country alpha2 being used: US
  ath: Regpair used: 0x3a
  ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  ieee80211 phy0: Atheros AR9100 MAC/BB Rev:7 AR2122 RF Rev:a2 mem=0xb80c0000, irq =2
  cfg80211: Calling CRDA for country: US
  cfg80211: Regulatory domain changed to country: US
  cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2700 mBm)
  cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 1700 mBm)
  cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (5490000 KHz - 5600000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (5650000 KHz - 5710000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 3000 mBm)
  ip_tables: (C) 2000-2006 Netfilter Core Team
  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  ar71xx-ehci ar71xx-ehci: Atheros AR91xx built-in EHCI controller
  ar71xx-ehci ar71xx-ehci: new USB bus registered, assigned bus number 1
  ar71xx-ehci ar71xx-ehci: irq 3, io mem 0x1b000000
  ar71xx-ehci ar71xx-ehci: USB 2.0 started, EHCI 1.00
  usb usb1: configuration #1 chosen from 1 choice
  hub 1-0:1.0: USB hub found
  hub 1-0:1.0: 1 port detected
  nf_conntrack version 0.5.0 (459 buckets, 1836 max)
  CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
  nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
  sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
  xt_time: kernel timezone is -0000
  IMQ driver loaded successfully.
  Hooking IMQ before NAT on PREROUTING.
  Hooking IMQ after NAT on POSTROUTING.
  ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
  Initializing USB Mass Storage driver...
  usbcore: registered new interface driver usb-storage
  USB Mass Storage support registered.
  fuse init (API version 7.13)
  eth1: link down
  device wlan0 entered promiscuous mode
  br-lan: port 2(wlan0) entering forwarding state
  ar71xx: pll_reg 0xb8050018: 0x13000a44
  eth1: link up (100Mbps/Full duplex)
  device wlan0 left promiscuous mode
  br-lan: port 2(wlan0) entering disabled state
  device wlan0 entered promiscuous mode
  br-lan: port 2(wlan0) entering forwarding state
  ar71xx-wdt: enabling watchdog timer
  usb 1-1: new high speed USB device using ar71xx-ehci and address 2
  usb 1-1: configuration #1 chosen from 1 choice
  scsi0 : SCSI emulation for USB Mass Storage devices
  usb-storage: device found at 2
  usb-storage: waiting for device to settle before scanning
  scsi 0:0:0:0: Direct-Access Mass Storage Device PQ: 0 ANSI: 0
  usb-storage: device scan complete
  sd 0:0:0:0: [sda] 312581806 512-byte logical blocks: (160 GB/149 GiB)
  sd 0:0:0:0: [sda] Write Protect is off
  sd 0:0:0:0: [sda] Mode Sense: 03 00 00 00
  sd 0:0:0:0: [sda] Assuming drive cache: write through
  sd 0:0:0:0: [sda] Assuming drive cache: write through
  sda: sda1 sda2 sda3
  sd 0:0:0:0: [sda] Assuming drive cache: write through
  sd 0:0:0:0: [sda] Attached SCSI disk
  root@OpenWrt:~#

Új hozzászólás Aktív témák