Új hozzászólás Aktív témák

• #17439 PistiSan addikt ArchElf #17438

  Új Válasz 2011-06-06 12:42:32 #17439

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  PistiSan

  addikt

  válasz ArchElf #17438 üzenetére

  Itt a kernel log tartalma:

  Linux version 2.6.32.25 (openwrt@ampere) (gcc version 4.3.3 (GCC) ) #1 Fri Nov 19 22:01:56 PST 2010
  CPU revision is: 00029029 (Broadcom BCM3302)
  ssb: Core 0 found: ChipCommon (cc 0x800, rev 0x14, vendor 0x4243)
  ssb: Core 1 found: Fast Ethernet (cc 0x806, rev 0x09, vendor 0x4243)
  ssb: Core 2 found: MIPS 3302 (cc 0x816, rev 0x08, vendor 0x4243)
  ssb: Core 3 found: USB 2.0 Host (cc 0x819, rev 0x02, vendor 0x4243)
  ssb: Core 4 found: MEMC SDRAM (cc 0x80F, rev 0x04, vendor 0x4243)
  ssb: Core 5 found: IEEE 802.11 (cc 0x812, rev 0x0D, vendor 0x4243)
  ssb: Core 6 found: Roboswitch (cc 0x81C, rev 0x02, vendor 0x4243)
  ssb: chipcommon status is 0x0
  ssb: Found rev 0 PMU (capabilities 0x04A63400)
  ssb: Initializing MIPS core...
  ssb: set_irq: core 0x0806, irq 4 => 4
  ssb: set_irq: core 0x0816, irq 5 => 2
  ssb: set_irq: core 0x0812, irq 2 => 5
  ssb: after irq reconfiguration
  ssb: core 0x0800, irq : 2(S) 3* 4 5 6 D I
  ssb: core 0x0806, irq : 2(S) 3 4* 5 6 D I
  ssb: core 0x0816, irq : 2(S)* 3 4 5 6 D I
  ssb: core 0x0819, irq : 2(S) 3 4 5 6* D I
  ssb: core 0x080f, irq : 2(S) 3 4 5 6 D I*
  ssb: core 0x0812, irq : 2(S) 3 4 5* 6 D I
  ssb: core 0x081c, irq : 2(S) 3 4 5 6 D I*
  ssb: Sonics Silicon Backplane found at address 0x18000000
  Serial init done.
  Determined physical RAM map:
  memory: 02000000 @ 00000000 (usable)
  Initrd not found or empty - disabling initrd
  Zone PFN ranges:
  Normal 0x00000000 -> 0x00002000
  Movable zone start PFN for each node
  early_node_map[1] active PFN ranges
  0: 0x00000000 -> 0x00002000
  On node 0 totalpages: 8192
  free_area_init_node: node 0, pgdat 802a09f0, node_mem_map 81000000
  Normal zone: 64 pages used for memmap
  Normal zone: 0 pages reserved
  Normal zone: 8128 pages, LIFO batch:0
  Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
  Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
  PID hash table entries: 128 (order: -3, 512 bytes)
  Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
  Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
  Primary instruction cache 16kB, VIPT, 4-way, linesize 16 bytes.
  Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
  Memory: 29496k/32768k available (2331k kernel code, 3272k reserved, 356k data, 136k init, 0k highmem)
  Hierarchical RCU implementation.
  NR_IRQS:128
  console [ttyS0] enabled
  Calibrating delay loop... 239.61 BogoMIPS (lpj=479232)
  Mount-cache hash table entries: 512
  NET: Registered protocol family 16
  bio: create slab <bio-0> at 0
  Switching to clocksource MIPS
  NET: Registered protocol family 2
  IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
  TCP established hash table entries: 1024 (order: 1, 8192 bytes)
  TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
  TCP: Hash tables configured (established 1024 bind 1024)
  TCP reno registered
  NET: Registered protocol family 1
  squashfs: version 4.0 (2009/01/31) Phillip Lougher
  Registering mini_fo version $Id$
  JFFS2 version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
  msgmni has been set to 57
  io scheduler noop registered
  io scheduler deadline registered (default)
  Serial: 8250/16550 driver, 2 ports, IRQ sharing enabled
  serial8250: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
  serial8250: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
  serial8250.0: ttyS0 at MMIO 0xb8000300 (irq = 3) is a 16550A
  serial8250.0: ttyS1 at MMIO 0xb8000400 (irq = 3) is a 16550A
  flash init: 0x1c000000 0x02000000
  Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
  Physically mapped flash: Found an alias at 0x800000 for the chip at 0x0
  Physically mapped flash: Found an alias at 0x1000000 for the chip at 0x0
  Physically mapped flash: Found an alias at 0x1800000 for the chip at 0x0
  CFI mfr 0x000000c2
  CFI id 0x000022cb
  Amd/Fujitsu Extended Query Table at 0x0040
  Amd/Fujitsu Extended Query version 1.1.
  number of CFI chips: 1
  cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
  Flash device: 0x800000 at 0x1fc00000
  bootloader size: 131072
  Creating 4 MTD partitions on "Physically mapped flash":
  0x000000000000-0x000000020000 : "cfe"
  0x000000020000-0x0000007f0000 : "linux"
  0x0000000fb000-0x0000007f0000 : "rootfs"
  mtd: partition "rootfs" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
  mtd: partition "rootfs" set to be root filesystem
  mtd: partition "rootfs_data" created automatically, ofs=2D0000, len=520000
  0x0000002d0000-0x0000007f0000 : "rootfs_data"
  0x0000007f0000-0x000000800000 : "nvram"
  b44.c:v2.0
  eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 48:5b:39:38:54:cc
  BCM47xx Watchdog Timer enabled (30 seconds, nowayout)
  TCP westwood registered
  NET: Registered protocol family 17
  802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
  All bugs added by David S. Miller <davem@redhat.com>
  VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
  Freeing unused kernel memory: 136k freed
  Please be patient, while OpenWrt loads ...
  diag: Detected 'ASUS WL-500g Premium V2'
  b44: eth0: Link is up at 100 Mbps, full duplex.
  b44: eth0: Flow control is off for TX and off for RX.
  roboswitch: Probing device eth0: found a 5325! It's a 5350.
  mini_fo: using base directory: /
  mini_fo: using storage directory: /overlay
  b44: eth0: powering down PHY
  b44: eth0: Link is up at 100 Mbps, full duplex.
  b44: eth0: Flow control is off for TX and off for RX.
  device eth0.0 entered promiscuous mode
  device eth0 entered promiscuous mode
  br-lan: port 1(eth0.0) entering forwarding state
  Compat-wireless backport release: compat-wireless-2010-10-14-7-gab01eca
  Backport based on wireless-testing.git master-2010-10-19
  cfg80211: Calling CRDA to update world regulatory domain
  PPP generic driver version 2.4.2
  NET: Registered protocol family 24
  SCSI subsystem initialized
  usbcore: registered new interface driver usbfs
  usbcore: registered new interface driver hub
  usbcore: registered new device driver usb
  b43-phy0: Broadcom 5354 WLAN found (core revision 13)
  ieee80211 phy0: Selected rate control algorithm 'minstrel_ht'
  Registered led device: b43-phy0::tx
  Registered led device: b43-phy0::rx
  Broadcom 43xx driver loaded [ Features: PL, GPIO LED Mask: 0x000f, Firmware-ID: FW13 ]
  Broadcom 43xx-legacy driver loaded [ Features: PLID, Firmware-ID: FW10 ]
  cfg80211: World regulatory domain updated:
  (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
  (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
  (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
  ip_tables: (C) 2000-2006 Netfilter Core Team
  ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  nf_conntrack version 0.5.0 (463 buckets, 1852 max)
  CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
  nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
  sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
  Initializing USB Mass Storage driver...
  usbcore: registered new interface driver usb-storage
  USB Mass Storage support registered.

  ez pedig a telepített csomagok listája

  root@OpenWrt:~# opkg list
  base-files - 43.10-r24045
  busybox - 1.15.3-2
  crda - 1.1.0-2
  dnsmasq - 2.55-5
  dropbear - 0.52-4
  fdisk - 2.13.0.1-4
  firewall - 1-20
  glib1 - 1.2.10-1
  hotplug2 - 1.0-beta-2
  iptables - 1.4.6-2
  iptables-mod-conntrack - 1.4.6-2
  iptables-mod-nat - 1.4.6-2
  iw - 0.9.21-1
  kernel - 2.6.32.25-1
  kmod-b43 - 2.6.32.25+2010-10-19-1
  kmod-b43legacy - 2.6.32.25+2010-10-19-1
  kmod-cfg80211 - 2.6.32.25+2010-10-19-1
  kmod-crc-ccitt - 2.6.32.25-1
  kmod-crypto-aes - 2.6.32.25-1
  kmod-crypto-arc4 - 2.6.32.25-1
  kmod-crypto-core - 2.6.32.25-1
  kmod-diag - 2.6.32.25-7.1
  kmod-fs-ext3 - 2.6.32.25-1
  kmod-fs-mbcache - 2.6.32.25-1
  kmod-ipt-conntrack - 2.6.32.25-1
  kmod-ipt-core - 2.6.32.25-1
  kmod-ipt-nat - 2.6.32.25-1
  kmod-ipt-nathelper - 2.6.32.25-1
  kmod-mac80211 - 2.6.32.25+2010-10-19-1
  kmod-nls-base - 2.6.32.25-1
  kmod-ppp - 2.6.32.25-1
  kmod-pppoe - 2.6.32.25-1
  kmod-scsi-core - 2.6.32.25-1
  kmod-switch - 2.6.32.25-3
  kmod-usb-core - 2.6.32.25-1
  kmod-usb-storage - 2.6.32.25-1
  kmod-usb2 - 2.6.32.25-1
  libc - 0.9.30.1-43.10
  libgcc - 4.3.3+cs-43.10
  libiptc - 1.4.6-2
  liblua - 5.1.4-7
  libncurses - 5.7-2
  libnl-tiny - 0.1-1
  libpthread - 0.9.30.1-43.10
  librt - 0.9.30.1-43.10
  libuci - 12012009.6-2
  libuci-lua - 12012009.6-2
  libxtables - 1.4.6-2
  lua - 5.1.4-7
  luci - 0.9+svn6512-1
  luci-admin-core - 0.9+svn6512-1
  luci-admin-full - 0.9+svn6512-1
  luci-admin-mini - 0.9+svn6512-1
  luci-app-firewall - 0.9+svn6512-1
  luci-app-initmgr - 0.9+svn6512-1
  luci-cbi - 0.9+svn6512-1
  luci-core - 0.9+svn6512-1
  luci-http - 0.9+svn6512-1
  luci-i18n-english - 0.9+svn6512-1
  luci-ipkg - 0.9+svn6512-1
  luci-lmo - 0.9+svn6512-1
  luci-nixio - 0.9+svn6512-1
  luci-sgi-cgi - 0.9+svn6512-1
  luci-sys - 0.9+svn6512-1
  luci-theme-base - 0.9+svn6512-1
  luci-theme-openwrt - 0.9+svn6512-1
  luci-uci - 0.9+svn6512-1
  luci-uvl - 0.9+svn6512-1
  luci-web - 0.9+svn6512-1
  mc - 4.6.2-1
  mtd - 13
  nano - 2.2.5-1
  nvram - 7
  opkg - 576-1
  ppp - 2.4.4-11
  ppp-mod-pppoe - 2.4.4-11
  uci - 12012009.6-2
  udevtrigger - 106-1
  uhttpd - 19
  wireless-tools - 29-4
  wpad-mini - 20100705-1
  root@OpenWrt:~#

  Mit gondolsz mi hiányozhat?

Új hozzászólás Aktív témák