Új hozzászólás Aktív témák

• #700 zodo nagyúr doc #699

  Új Válasz 2009-08-06 18:57:31 #700

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  zodo

  nagyúr

  válasz doc #699 üzenetére

  Ok, te vagy az okosabb nem ellenkezem tovább! Igazad van, majd tanulok!

  de az ubi megcsinál mindent alapból

  Megy a netem meg a bill. is magyar lett, de nem tudok sem ff-ből sem konquer-ből hsz-t küldeni. Megáll valami hibával. ( lehet,hosszú a hsz. )
  Szerk: Most már biztos,hogy hosszú mert innen se küldte el a teljes fájl tartalmat, ezért töröltem az elejét.

  Átmentettem pendrive-on az xorg.conf-om. Megnéznéz, hátha látsz benne valami érdekes dolgot ill. visszaírhatnád ,hogy mit és hova másoljak be a felbontás beállítás véget.

  # **********************************************************************
  # Monitor section
  # **********************************************************************
  
  # Any number of monitor sections may be present
  
  Section "Monitor"
  
  Identifier "My Monitor"
  
  # HorizSync is in kHz unless units are specified.
  # HorizSync may be a comma separated list of discrete values, or a
  # comma separated list of ranges of values.
  # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
  # USER MANUAL FOR THE CORRECT NUMBERS.
  
  HorizSync 31.5 - 50.0
  
  # HorizSync 30-64 # multisync
  # HorizSync 31.5, 35.2 # multiple fixed sync frequencies
  # HorizSync 15-25, 30-50 # multiple ranges of sync frequencies
  
  # VertRefresh is in Hz unless units are specified.
  # VertRefresh may be a comma separated list of discrete values, or a
  # comma separated list of ranges of values.
  # NOTE: THE VALUES HERE ARE EXAMPLES ONLY. REFER TO YOUR MONITOR'S
  # USER MANUAL FOR THE CORRECT NUMBERS.
  
  VertRefresh 40-90
  
  EndSection
  
  
  # **********************************************************************
  # Graphics device section
  # **********************************************************************
  
  # Any number of graphics device sections may be present
  
  Section "Device"
  Identifier "VESA Framebuffer"
  Driver "vesa"
  #VideoRam 4096
  # Insert Clocks lines here if appropriate
  EndSection
  
  # **********************************************************************
  # Screen sections
  # **********************************************************************
  
  # Any number of screen sections may be present. Each describes
  # the configuration of a single screen. A single specific screen section
  # may be specified from the X server command line with the "-screen"
  # option.
  Section "Screen"
  Identifier "Screen 1"
  Device "VESA Framebuffer"
  Monitor "My Monitor"
  
  # If your card can handle it, a higher default color depth (like 24 or 32)
  # is highly recommended.
  
  # DefaultDepth 8
  # DefaultDepth 16
  DefaultDepth 24
  # DefaultDepth 32
  
  # "1024x768" is also a conservative usable default resolution. If you
  # have a better monitor, feel free to try resolutions such as
  # "1152x864", "1280x1024", "1600x1200", and "1800x1400" (or whatever your
  # card/monitor can produce)
  
  Subsection "Display"
  Depth 8
  Modes "1024x768" "800x600" "640x480"
  EndSubsection
  Subsection "Display"
  Depth 16
  Modes "1024x768" "800x600" "640x480"
  EndSubsection
  Subsection "Display"
  Depth 24
  Modes "1024x768" "800x600" "640x480"
  EndSubsection
  Subsection "Display"
  Depth 32
  Modes "1024x768" "800x600" "640x480"
  EndSubsection
  
  EndSection
  
  # **********************************************************************
  # ServerLayout sections.
  # **********************************************************************
  
  # Any number of ServerLayout sections may be present. Each describes
  # the way multiple screens are organised. A specific ServerLayout
  # section may be specified from the X server command line with the
  # "-layout" option. In the absence of this, the first section is used.
  # When now ServerLayout section is present, the first Screen section
  # is used alone.
  
  Section "ServerLayout"
  
  # The Identifier line must be present
  Identifier "Simple Layout"
  
  # Each Screen line specifies a Screen section name, and optionally
  # the relative position of other screens. The four names after
  # primary screen name are the screens to the top, bottom, left and right
  # of the primary screen. In this example, screen 2 is located to the
  # right of screen 1.
  
  Screen "Screen 1"
  
  # Each InputDevice line specifies an InputDevice section name and
  # optionally some options to specify the way the device is to be
  # used. Those options include "CorePointer", "CoreKeyboard" and
  # "SendCoreEvents".
  
  InputDevice "Mouse1" "CorePointer"
  InputDevice "Keyboard1" "CoreKeyboard"
  
  EndSection

  [ Szerkesztve ]

Új hozzászólás Aktív témák