Új hozzászólás Aktív témák

• #3790 Drótszamár őstag

  Új Válasz 2014-04-10 22:04:04 #3790

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  Drótszamár

  őstag

  Üdv!

  Olimex Lime A10-es mini pc-re szeretnék Openwrt-t tenni.

  Letöltöttem a megfelelő fájlokat innen és a leírásnak megfelelően sd kártyára írtam őket.

  Sajnos nincs hálózatom, és totál elakadtam. Mi nem jó? Esetleg pont belenyúltam egy nem működő snapshotba?

  Az Openwrt-s weboldalon van pár extra sor, ami nálam nincs:
  [ 7.532956] usbcore: registered new interface driver rt73usb
  [ 7.551074] usbcore: registered new interface driver rtl8187
  [ 7.574839] usbcore: registered new interface driver rt2500usb
  [ 7.594748] usbcore: registered new interface driver rt2800usb
  [ 7.613783] usbcore: registered new interface driver rtl8192cu

  Ez lenne a gond?

  Kötöttem rá USB-s soros átalakítót, ez fogad a konzolon:

  U-Boot SPL 2014.01-rc1 (Mar 26 2014 - 04:36:27)
  Board: A10-OLinuXino-Lime
  DRAM: 512 MiB
  CPU: 1008000000Hz, AXI/AHB/APB: 3/2/2
  spl: not an uImage at 1600
  
  
  U-Boot 2014.01-rc1 (Mar 26 2014 - 04:36:27) Allwinner Technology
  
  CPU: Allwinner A10 (SUN4I)
  Board: A10-OLinuXino-Lime
  I2C: ready
  DRAM: 512 MiB
  MMC: SUNXI SD/MMC: 0
  *** Warning - bad CRC, using default environment
  
  In: serial
  Out: serial
  Err: serial
  Net: emac
  Hit any key to stop autoboot: 0
  reading uEnv.txt
  240 bytes read in 2 ms (117.2 KiB/s)
  Loaded environment from uEnv.txt
  Running uenvcmd ...
  reading uImage
  2520728 bytes read in 113 ms (21.3 MiB/s)
  reading dtb
  16195 bytes read in 4 ms (3.9 MiB/s)
  ## Booting kernel from Legacy Image at 46000000 ...
  Image Name: ARM OpenWrt Linux-3.13.2
  Created: 2014-03-26 12:25:59 UTC
  Image Type: ARM Linux Kernel Image (uncompressed)
  Data Size: 2520664 Bytes = 2.4 MiB
  Load Address: 40008000
  Entry Point: 40008000
  Verifying Checksum ... OK
  ## Flattened Device Tree blob at 49000000
  Booting using the fdt blob at 0x49000000
  Loading Kernel Image ... OK
  Using Device Tree in place at 49000000, end 49006f42
  
  Starting kernel ...
  
  [ 0.000000] Booting Linux on physical CPU 0x0
  [ 0.000000] Linux version 3.13.2 (openwrt@gb-13) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.01 r40018) ) #1 SMP PREEMPT Wed Mar 26 12:25:50 UTC 2014
  [ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c5387d
  [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
  [ 0.000000] Machine model: Olimex A10-OLinuXino-LIME
  [ 0.000000] Memory policy: Data cache writeback
  [ 0.000000] CPU: All CPU(s) started in SVC mode.
  [ 0.000000] PERCPU: Embedded 7 pages/cpu @c0978000 s7040 r8192 d13440 u32768
  [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
  [ 0.000000] Kernel command line: console=ttyS0,115200 earlyprintk rootwait root=/dev/mmcblk0p2
  [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
  [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
  [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
  [ 0.000000] Memory: 514148K/524288K available (3567K kernel code, 158K rwdata, 1004K rodata, 186K init, 606K bss, 10140K reserved, 0K highmem)
  [ 0.000000] Virtual kernel memory layout:
  [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
  [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
  [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
  [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
  [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
  [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
  [ 0.000000] .text : 0xc0008000 - 0xc047ef04 (4572 kB)
  [ 0.000000] .init : 0xc047f000 - 0xc04adb80 ( 187 kB)
  [ 0.000000] .data : 0xc04ae000 - 0xc04d5a7c ( 159 kB)
  [ 0.000000] .bss : 0xc04d5a7c - 0xc056d5a8 ( 607 kB)
  [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
  [ 0.000000] Preemptible hierarchical RCU implementation.
  [ 0.000000] RCU restricting CPUs from NR_CPUS=4 to nr_cpu_ids=1.
  [ 0.000000] NR_IRQS:16 nr_irqs:16 16
  [ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956969942ns
  [ 0.000000] Console: colour dummy device 80x30
  [ 0.000204] Calibrating delay loop... 1001.88 BogoMIPS (lpj=5009408)
  [ 0.090058] pid_max: default: 32768 minimum: 301
  [ 0.090180] Mount-cache hash table entries: 512
  [ 0.093997] CPU: Testing write buffer coherency: ok
  [ 0.094268] CPU0: thread -1, cpu 0, socket -1, mpidr 0
  [ 0.094316] Setting up static identity map for 0x40011940 - 0x40011974
  [ 0.130209] Brought up 1 CPUs
  [ 0.130221] SMP: Total of 1 processors activated.
  [ 0.130228] CPU: All CPU(s) started in SVC mode.
  [ 0.130923] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
  [ 0.131093] pinctrl core: initialized pinctrl subsystem
  [ 0.131389] regulator-dummy: no parameters
  [ 0.131638] NET: Registered protocol family 16
  [ 0.132069] DMA: preallocated 256 KiB pool for atomic coherent allocations
  [ 0.137876] bio: create slab <bio-0> at 0
  [ 0.138328] reg-fixed-voltage ahci-5v.1: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/ahci_pwr_pin@1, deferring probe
  [ 0.138354] platform ahci-5v.1: Driver reg-fixed-voltage requests probe deferral
  [ 0.138381] reg-fixed-voltage usb1-vbus.2: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb1_vbus_pin@0, deferring probe
  [ 0.138396] platform usb1-vbus.2: Driver reg-fixed-voltage requests probe deferral
  [ 0.138419] reg-fixed-voltage usb2-vbus.3: could not find pctldev for node /soc@01c00000/pinctrl@01c20800/usb2_vbus_pin@0, deferring probe
  [ 0.138435] platform usb2-vbus.3: Driver reg-fixed-voltage requests probe deferral
  [ 0.138802] SCSI subsystem initialized
  [ 0.139181] usbcore: registered new interface driver usbfs
  [ 0.139241] usbcore: registered new interface driver hub
  [ 0.139352] usbcore: registered new device driver usb
  [ 0.139455] pps_core: LinuxPPS API ver. 1 registered
  [ 0.139463] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
  [ 0.139489] PTP clock support registered
  [ 0.140212] Switched to clocksource timer
  [ 0.145083] NET: Registered protocol family 2
  [ 0.145726] TCP established hash table entries: 4096 (order: 2, 16384 bytes)
  [ 0.145777] TCP bind hash table entries: 4096 (order: 3, 32768 bytes)
  [ 0.145838] TCP: Hash tables configured (established 4096 bind 4096)
  [ 0.145902] TCP: reno registered
  [ 0.145915] UDP hash table entries: 256 (order: 1, 8192 bytes)
  [ 0.145936] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
  [ 0.146135] NET: Registered protocol family 1
  [ 0.147082] audit: initializing netlink socket (disabled)
  [ 0.147128] type=2000 audit(0.140:1): initialized
  [ 0.153241] VFS: Disk quotas dquot_6.5.2
  [ 0.153453] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
  [ 0.154805] squashfs: version 4.0 (2009/01/31) Phillip Lougher
  [ 0.154819] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
  [ 0.155299] msgmni has been set to 1004
  [ 0.156102] io scheduler noop registered
  [ 0.156116] io scheduler deadline registered
  [ 0.156149] io scheduler cfq registered (default)
  [ 0.156354] platform 1c13400.phy: Driver sun4i-usb-phy requests probe deferral
  [ 0.158330] sunxi-pinctrl 1c20800.pinctrl: initialized sunXi PIO driver
  [ 0.188868] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled
  [ 0.211603] 1c28000.serial: ttyS0 at MMIO 0x1c28000 (irq = 26, base_baud = 1500000) is a U6_16550A
  [ 0.713245] console [ttyS0] enabled
  [ 0.717303] platform 1c18000.sata: Driver ahci-sunxi requests probe deferral
  [ 0.725121] 1c0b080.mdio supply phy not found, using dummy regulator
  [ 0.731629] libphy: sun4i_mii_bus: probed
  [ 0.770935] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
  [ 0.777460] ehci-platform: EHCI generic platform driver
  [ 0.782837] platform 1c14000.usb: Driver ehci-platform requests probe deferral
  [ 0.790097] platform 1c1c000.usb: Driver ehci-platform requests probe deferral
  [ 0.797484] usbcore: registered new interface driver usb-storage
  [ 0.803704] mousedev: PS/2 mouse device common for all mice
  [ 0.809858] sunxi-wdt 1c20c90.watchdog: Watchdog enabled (timeout=16 sec, nowayout=0)
  [ 0.818521] sunxi-mmc 1c0f000.mmc: Got CD GPIO #225.
  [ 0.823688] sunxi-mmc 1c0f000.mmc: base:0xe08e2000 irq:18
  [ 0.829742] TCP: cubic registered
  [ 0.833142] Initializing XFRM netlink socket
  [ 0.837435] NET: Registered protocol family 17
  [ 0.842031] Bridge firewalling registered
  [ 0.846048] 8021q: 802.1Q VLAN Support v1.8
  [ 0.850502] Registering SWP/SWPB emulation handler
  [ 0.855573] registered taskstats version 1
  [ 0.860171] ahci-5v: 5000 mV
  [ 0.863518] usb1-vbus: 5000 mV
  [ 0.866936] usb2-vbus: 5000 mV
  [ 0.940231] ahci-sunxi 1c18000.sata: controller can't do PMP, turning off CAP_PMP
  [ 0.947717] ahci-sunxi 1c18000.sata: forcing PORTS_IMPL to 0x1
  [ 0.953615] ahci-sunxi 1c18000.sata: AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl platform mode
  [ 0.962590] ahci-sunxi 1c18000.sata: flags: ncq sntf pm led clo only pio slum part ccc
  [ 0.971363] scsi0 : ahci_platform
  [ 0.974941] ata1: SATA max UDMA/133 mmio [mem 0x01c18000-0x01c18fff] port 0x100 irq 21
  [ 0.984165] ehci-platform 1c14000.usb: EHCI Host Controller
  [ 0.990924] ehci-platform 1c14000.usb: new USB bus registered, assigned bus number 1
  [ 0.998776] ehci-platform 1c14000.usb: irq 19, io mem 0x01c14000
  [ 1.020223] ehci-platform 1c14000.usb: USB 2.0 started, EHCI 1.00
  [ 1.026489] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
  [ 1.033295] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  [ 1.040557] usb usb1: Product: EHCI Host Controller
  [ 1.045432] usb usb1: Manufacturer: Linux 3.13.2 ehci_hcd
  [ 1.051859] usb usb1: SerialNumber: 1c14000.usb
  [ 1.056836] hub 1-0:1.0: USB hub found
  [ 1.060671] hub 1-0:1.0: 1 port detected
  [ 1.065070] ehci-platform 1c1c000.usb: EHCI Host Controller
  [ 1.070722] ehci-platform 1c1c000.usb: new USB bus registered, assigned bus number 2
  [ 1.078594] ehci-platform 1c1c000.usb: irq 22, io mem 0x01c1c000
  [ 1.100233] ehci-platform 1c1c000.usb: USB 2.0 started, EHCI 1.00
  [ 1.106479] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
  [ 1.113287] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
  [ 1.120515] usb usb2: Product: EHCI Host Controller
  [ 1.125389] usb usb2: Manufacturer: Linux 3.13.2 ehci_hcd
  [ 1.130796] usb usb2: SerialNumber: 1c1c000.usb
  [ 1.135669] hub 2-0:1.0: USB hub found
  [ 1.139449] hub 2-0:1.0: 1 port detected
  [ 1.144681] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
  [ 1.250301] mmc0: host does not support reading read-only switch. assuming write-enable.
  [ 1.340237] ata1: SATA link down (SStatus 0 SControl 300)
  [ 1.360319] Waiting for root device /dev/mmcblk0p2...
  [ 1.425309] mmc0: new high speed SDHC card at address aaaa
  [ 1.431098] isa bounce pool size: 16 pages
  [ 1.435316] mmcblk0: mmc0:aaaa SU08G 7.40 GiB
  [ 1.441094] mmcblk0: p1 p2
  [ 1.471151] EXT4-fs (mmcblk0p2): couldn't mount as ext3 due to feature incompatibilities
  [ 1.479962] EXT4-fs (mmcblk0p2): couldn't mount as ext2 due to feature incompatibilities
  [ 1.490995] EXT4-fs (mmcblk0p2): mounted filesystem without journal. Opts: (null)
  [ 1.498663] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
  [ 1.505729] Freeing unused kernel memory: 184K (c047f000 - c04ad000)
  procd: Console is alive
  procd: - watchdog -
  procd: - preinit -
  probing /dev/mmcblk0 for uboot env data
  Detected generic sunxi // generic sunxi
  [ 1.755256] random: mktemp urandom read with 15 bits of entropy available
  Press the [f] key and hit [enter] to enter failsafe mode
  Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
  mounting /dev/root[ 3.816491] EXT4-fs (mmcblk0p2): warning: mounting unchecked fs, running e2fsck is recommended
  
  [ 3.833447] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
  procd: - early -
  procd: - watchdog -
  procd: - ubus -
  procd: - init -
  Please press Enter to activate this console.
  [ 6.171085] NET: Registered protocol family 10
  [ 6.182187] nf_conntrack version 0.5.0 (8036 buckets, 32144 max)
  [ 6.209511] ip6_tables: (C) 2000-2006 Netfilter Core Team
  [ 6.239240] ip_tables: (C) 2000-2006 Netfilter Core Team
  [ 6.317182] xt_time: kernel timezone is -0000
  [ 6.349966] PPP generic driver version 2.4.2
  [ 6.361686] NET: Registered protocol family 24
  procd: - init complete -
  [ 94.984373] random: nonblocking pool is initialized
  
  
  
  BusyBox v1.19.4 (2014-03-26 12:13:55 UTC) built-in shell (ash)
  Enter 'help' for a list of built-in commands.
  
  _______ ________ __
  | |.-----.-----.-----.| | | |.----.| |_
  | - || _ | -__| || | | || _|| _|
  |_______|| __|_____|__|__||________||__| |____|
  |__| W I R E L E S S F R E E D O M
  -----------------------------------------------------
  BARRIER BREAKER (Bleeding Edge, r40018)
  -----------------------------------------------------
  * 1/2 oz Galliano Pour all ingredients into
  * 4 oz cold Coffee an irish coffee mug filled
  * 1 1/2 oz Dark Rum with crushed ice. Stir.
  * 2 tsp. Creme de Cacao
  -----------------------------------------------------
  root@OpenWrt:/# ifconfig
  lo Link encap:Local Loopback
  inet addr:127.0.0.1 Mask:255.0.0.0
  inet6 addr: ::1/128 Scope:Host
  UP LOOPBACK RUNNING MTU:65536 Metric:1
  RX packets:768 errors:0 dropped:0 overruns:0 frame:0
  TX packets:768 errors:0 dropped:0 overruns:0 carrier:0
  collisions:0 txqueuelen:0
  RX bytes:52896 (51.6 KiB) TX bytes:52896 (51.6 KiB)
  
  root@OpenWrt:/#

  ( 2b || !2b ) az itt a kérdés...

Új hozzászólás Aktív témák