Új hozzászólás Aktív témák

• #134 csontika tag parandroid #109

  Új Válasz 2005-11-20 22:08:54 #134

  Új hozzászólás

  Összes hozzászólása itt Válaszok az összes hozzászólására itt Válaszok erre a hozzászólásra

  Privát üzenet küldése

  

  csontika

  tag

  válasz parandroid #109 üzenetére

  Sikerült az átalakitás!
  
  Teljesen jól működik ezzel a leírással.
  Fontos, hogy csak a megadott knoppixal működik, 4.0-sal nem. Attól meg nem kell félni, hogy kari berakásakor néhányszor kifagyott a noti
  
  I have a solution thanks to whiteheat and druid cz from x1000 forums that allows you to use any Intel Pro Wireless 2200BG card inside your HP laptop.
  
  Before, I received the error 104: unsupported wireless card, now my NC8000 laptop will boot perfectly. Now you can buy your card for < ÂL25.00 instead of HP's ÂL60 + vat + p&p.
  
  First off if you don't have linux installed you will need to go to www.knoppix.org and download KNOPPIX_V3.8.2-2005-05-05-EN.iso, then burn the cd
  
  You need to have the card install during the boot sequence so, have your laptop open and bootup, when you see the boot:_ line insert the card then press enter. Knoppix will autodetect the card & the bios wont complain.
  
  Once knoppix has booted:
  
  Click on the penguin on the taskbar and select ''Root Shell'', then the following command (from now on any line that begins with a # is a command to be typed at the Root prompt:
  #iwconfig
  You will get a list of ethernet adapters, eth0, eth1 etc. The wireless one should be quite obvious from the text displayed after it with all the wireless parameters!
  #ethtool -e ethX
  Obviously replace the 'X' with the index of your wireless card you found above.
  You will get a hex dump of the 256 bytes of EEPROM data.
  Note: There is nothing dangerous in the above steps at all.
  
  If you want to writing to your EEPROM (You can seriously screw your card up so be careful ):
  
  #mkdir /usr/tmp
  #cd /usr/tmp
  #wget http://www.geocities.com/sonyirclib/ipw2200.tar.gz
  >
  
  N.B. This file has already been patched to allow writing to the eeprom
  
  #tar xvzf ipw2200.tar.gz
  #cd ipw2200-1.0.3
  #sh unload
  #sh load
  
  Now all that you need to do is write to the eeprom. If your card is from Europe:
  
  #ethtool -E eth0 magic 0x2200 offset 0x8 value 0xf6
  #ethtool -E eth0 magic 0x2200 offset 0x9 value 0x12
  #ethtool -E eth0 magic 0x2200 offset 0xa value 0x3c
  #ethtool -E eth0 magic 0x2200 offset 0xb value 0x10
  
  If it is from the US:
  
  ethtool -E eth0 magic 0x2200 offset 0x8 value 0xf5
  ethtool -E eth0 magic 0x2200 offset 0x9 value 0x12
  ethtool -E eth0 magic 0x2200 offset 0xa value 0x3c
  ethtool -E eth0 magic 0x2200 offset 0xb value 0x10
  
  N.B. the -E must be uppercase for writing to work.
  
  Now reboot your computer and you should no longer get the error 104...!
  
  For more details see: http://www.x1000forums.com/index.php?showtopic=8737
  
  Regard
  
  Mindenkinek sok szerencsét, és sok nyugtatót!
  
  
  
  elötte :
  
  [link]
  
  utána:
  
  [link]
  
  
  
  [Szerkesztve]

  A rendszeres tanulás a tudás egyik rokona!

Új hozzászólás Aktív témák