- NVIDIA GeForce RTX 5080 / 5090 (GB203 / 202)
- Canon EOS DSLR topic
- AMD Ryzen 9 / 7 / 5 9***(X) "Zen 5" (AM5)
- Intel Core i5 / i7 / i9 "Alder Lake-Raptor Lake/Refresh" (LGA1700)
- Forrmell.enn
- Vélemény: nem úgy tűnik, de Lip-Bu Tan most menti meg az Intelt
- AMD Navi Radeon™ RX 5xxx sorozat
- HiFi műszaki szemmel - sztereó hangrendszerek
- Hobby elektronika
- Milyen joysticket vegyek?
Új hozzászólás Aktív témák
-
DP_Joci
tag
Szia Szirty,
Amikor arra gondoltam, hogy megkeresed a nullás címet, akkor az AS-i masteren gondoltam, hogy a nullás AS-i címet keresed meg.
Találtam egy manualt: C79000−G8976−C149−04 google-ba beírva az első pdf nálam.
De az a lényeg, hogy gomb nyommással elméletileg lehet a meglévő slave címeket megjeleníteni, és emlékeim szerint változtatni is:Configuring using Buttons
Preparation for Button Configuration
Make sure that the following situation applies:
_ The PLC CPU must be switched to STOP.
_ The CP 343-2 and all AS-i slaves must be connected to the AS-interface and
supplied with power.
_ The AS-i slaves must have unique addresses other than “0”.
Setting the Configuration with Buttons
1. Check whether the CP 343-2 is in “configuration mode” (”CM” LED is lit).
If the ”CM” LED is not lit, change the CP 343-2 to the configuration mode with
the “SET” button.
2. Check whether all the slaves connected to the AS-interface exist and are
displayed.
3. Press the SET button. This configures the CP 343-2; in other words, the
detected actual configuration is stored as the default in the non-volatile
EEPROM. At the same time, the CP 343-2 is changed to the protected mode;
the “CM” LED goes off. (See Section 1.5 > SET button)
The “CER” LED also goes off since following configuration, the “expected
configuration” stored on the CP 343-2 matches the “actual configuration” on the
AS-Interface.
Note
Changing from the configuration mode to the protected mode is only possible
when there is no AS-i slave with address 0 connected to the AS-Interface. If a
slave 0 is connected, the “SF” LED lights up when the SET button is pressed.
If you run a button configuration when there is no AS-i power supply (APF state) or
when no AS-i slaves are connected, all the internal lists are set to their default
values. In particular, all the AS-i parameters are set to = FHex and the
AutoAddress_Enable bit is set to = 1.Egyébként ezzel egyszerűbb:
http://www.ifm.com/products/hu/ds/AC1154.htm
Új hozzászólás Aktív témák
- Formula-1
- NVIDIA GeForce RTX 5080 / 5090 (GB203 / 202)
- Canon EOS DSLR topic
- DOOM - The Dark Ages
- AMD Ryzen 9 / 7 / 5 9***(X) "Zen 5" (AM5)
- Motoros topic
- Luck Dragon: Asszociációs játék. :)
- Intel Core i5 / i7 / i9 "Alder Lake-Raptor Lake/Refresh" (LGA1700)
- Viccrovat
- One otthoni szolgáltatások (TV, internet, telefon)
- További aktív témák...
- SZÉP Lenovo ThinkPad P15 G2 Tervező Laptop -75% 15,6" i9-11950H 64/2TB RTX A4000 8GB UHD OLED
- Szép! Lenovo Thinkpad T14s G2 Üzleti "Golyóálló" Laptop 14" -50% i7-1185G7 4Mag 16GB/512GB FHD IPS
- Eladó Apple MacBook Pro 13" A1706 (Late 2017, Silver - EMC 3163)
- Amazfit GTR 2 Classic okosóra dobozában töltőkábellel
- Mac mini M1 chip 8 magos CPU-val, 8 magos GPU-val
- Apple iPhone 14 128GB , Kártyafüggetlen
- BESZÁMÍTÁS! LENOVO Ideapad Gaming 3 notebook - i5 11320H 16GB DDR4 256GB+1TB SSD GTX 1650 4GB WIN11
- ÚJ Lenovo ThinkPad X13 Gen 5 - 13.3" WUXGA IPS - Ultra 5 135U - 16GB - 512GB - Win11 - 2,5 év gari
- Telefon felvásárlás!! Samsung Galaxy A16, Samsung Galaxy A26, Samsung Galaxy A36, Samsung Galaxy A56
- 118 - Lenovo Legion Pro 5 (16ARX8) - AMD Ryzen 9 7945HX, RTX 4070 (ELKELT)
Állásajánlatok
Cég: Promenade Publishing House Kft.
Város: Budapest
Cég: CAMERA-PRO Hungary Kft
Város: Budapest